If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Mount Bindings
I'm new to the group and hope the flames will be kept to a minimum. My 6
year old was skiing on a pair of tiny Elan's which have relatively new and in excellent shape Salomon 300 bindings. I managed to get a great deal on a new set of K2 Magic from a Sports Authority ($50) and want to use the 300 bindings on these K2's but with the exact same boots. My son's weight has not changed much since last season. This binding simply use 4 screws in the back and 3 in the front. Can I mount these bindings with the exact same measurements (distance between front binding and back binding) from the old ski but percentage out for the correct location on the new skis (110's)? The local shops want $50 just to mount bindings because I didn't buy the boots or skis there. I know how to adjust bindings for the additional weight and skill level and check for motion etc... but need to know the specifics of drilling (measured depth) and glue (what kind?). Any help is appreciate. Please save the "pay the $50" flames. I'd like to know if this is as simple as it looks. Cheers |
#2
|
|||
|
|||
Mount Bindings
Schmoe wrote:
I'm new to the group and hope the flames will be kept to a minimum. My 6 year old was skiing on a pair of tiny Elan's which have relatively new and in excellent shape Salomon 300 bindings. I managed to get a great deal on a new set of K2 Magic from a Sports Authority ($50) and want to use the 300 bindings on these K2's but with the exact same boots. My son's weight has not changed much since last season. This binding simply use 4 screws in the back and 3 in the front. Can I mount these bindings with the exact same measurements (distance between front binding and back binding) from the old ski but percentage out for the correct location on the new skis (110's)? The local shops want $50 just to mount bindings because I didn't buy the boots or skis there. I know how to adjust bindings for the additional weight and skill level and check for motion etc... but need to know the specifics of drilling (measured depth) and glue (what kind?). Any help is appreciate. Please save the "pay the $50" flames. I'd like to know if this is as simple as it looks. Cheers To be quite honest, I do all of the work on my skis myself - except for mounting bindings. In reality it may be a simple process, but I feel safer knowing that someone with experience has mounted them for me. -- Chester Bullock, Ethical, custom website hosting, design and programming Tenxible Solutions, http://www.tenxible.com Web Based Autoresponder and DRIP system, http://www.toolsre.com AIM: tenxible YahooIM: ccb247 |
#3
|
|||
|
|||
Mount Bindings
Schmoe wrote:
I'm new to the group and hope the flames will be kept to a minimum. My 6 year old was skiing on a pair of tiny Elan's which have relatively new and in excellent shape Salomon 300 bindings. I managed to get a great deal on a new set of K2 Magic from a Sports Authority ($50) and want to use the 300 bindings on these K2's but with the exact same boots. My son's weight has not changed much since last season. This binding simply use 4 screws in the back and 3 in the front. Can I mount these bindings with the exact same measurements (distance between front binding and back binding) from the old ski but percentage out for the correct location on the new skis (110's)? The local shops want $50 just to mount bindings because I didn't buy the boots or skis there. I know how to adjust bindings for the additional weight and skill level and check for motion etc... but need to know the specifics of drilling (measured depth) and glue (what kind?). Any help is appreciate. Please save the "pay the $50" flames. I'd like to know if this is as simple as it looks. You need to know several things Where should the boot be on the new skis? Some skiboots don't even have the center mark, so right away you're up against dealing with ski cord-length and boot toe position issues - a whole art unto itself. Assuming the boots and the skis have center marks, you position the boots at the right location, set the binding heels to the middle of their track, place the toe and heal bindings pieces appropriately, mark, centerpunch, and drill the holes, screw the binding down, set the forward pressure adjustment, set the DIN adjustment, and check for proper release function and release force. (BTW, you mount the second ski relative to the first ski binding position; not by going through the positioning process again. You want matched mountings, even if the ski position marks are slightly askew.) Problems occur in drilling the holes right through the base - using a drill press makes that easy to avoid; and in mis-drilling - proper center punching can control mis-drilling. But the primary problem is in testing release function and force - and this is why most will advise against doing your own mounting, including me. The shop charges alot because they have an expensive, complex machine to amortise that does these tests accurately. So there's some risk in doing it yourself: it can be done. BTW, my boy spiraled his tibia when he was 5 - landed a jump wrong. The bindings were professionally mounted and checked; it didn't help. Skiing's a risk sport. I recommend you not mount your own, but get a shop to mount and test the bindings. (However, you can get a shop to adjust and test bindings that are already mounted - probably for about half the mount price. They won't know you mounted them yourself, if you did it right.) |
#4
|
|||
|
|||
Mount Bindings
Schmoe wrote:
I'm new to the group and hope the flames will be kept to a minimum. My 6 year old was skiing on a pair of tiny Elan's which have relatively new and in excellent shape Salomon 300 bindings. I managed to get a great deal on a new set of K2 Magic from a Sports Authority ($50) and want to use the 300 bindings on these K2's but with the exact same boots. My son's weight has not changed much since last season. This binding simply use 4 screws in the back and 3 in the front. Can I mount these bindings with the exact same measurements (distance between front binding and back binding) from the old ski but percentage out for the correct location on the new skis (110's)? The local shops want $50 just to mount bindings because I didn't buy the boots or skis there. I know how to adjust bindings for the additional weight and skill level and check for motion etc... but need to know the specifics of drilling (measured depth) and glue (what kind?). Any help is appreciate. Please save the "pay the $50" flames. I'd like to know if this is as simple as it looks. This is not a flame, but the standard advice is to have this work done by a qualified professional. It's not rocket science, but since you don't have access to the measurement tools that allow you to verify that it's been done right, its not a good idea to do it yourself. If you shop around you should be able to find a place to mount them for less than $50. -- //-Walt // // The Volkl Conspiracy |
#5
|
|||
|
|||
Mount Bindings
Mount-your-own? Along with the recommendations already posted here ... Assuming the bindings were correctly mounted before, it would not be too difficult to make a template off the old skis, and transfer that drilling pattern to the new skis. Tooling you'll need -- * drill press * clamp equipment to hold ski rigidly in place on drill press * correct size drill bits * correct size taps * correct size NEW mounting hardware plus misc. stuff like maybe a transfer punch set to make a sample template to compare to the old skis, misc. adhesives and shop chemicals, etc. etc. Oh, and a way to limit the depth of the drilled hole. Some drill presses have an attachment for this; if you use it you'll also need a depth gauge to verify the hole depth. Wait, I forgot, your taps have to be bottoming taps, or otherwise the screws will enlarge the bottom of the hole and distort the topskin, forcing the bindings up from the topskin and jeopardizing their action and/or causing them to fall off ... Wait, I forgot, the necessary skills are not rocket science but you DO need to know how to operate the machinery AND make accurate measurements and markings -- did I mention enough squares and straightedges to ensure that the bindings are parallel to the centerline of the skis? A yardstick is not sufficient, but a 36" steel machinist's rule is a good start. You'll also need a machinist's scale to verify hole positions before you start drilling... Since I already have most of the tooling, I'd risk mounting my own bindings if the new skis AND bindings were free or next-to-free, AND if I didn't have anything better to do. I'm guessing it'd take me a few hours to do. And that doesn't include the maintenance on my existing tooling investment, or the new stuff I'd need to buy, which would push my out-of-pocket cost close to $50. In short, mounting bindings is well within the realm of something that you could do in your basement or garage shop, assuming you had the tooling and training, but most people choose to farm out this little bit of work because it's just not cost-effective to do it at home. The up-side? If you mount your own and something goes wrong, it's easy to beat up the last ski tuner who worked on your sticks. I have a little story about a ski patroller who caught me readjusting my bindings at the top of the lift ... |
#6
|
|||
|
|||
Mount Bindings
On Fri, 14 Nov 2003 15:23:01 -0000, wrote:
Mount-your-own? Along with the recommendations already posted here ... Assuming the bindings were correctly mounted before, it would not be too difficult to make a template off the old skis, and transfer that drilling pattern to the new skis. Tooling you'll need -- * drill press Not in any of the shops I've seen doing mountings. JP *************** One less nit. |
#7
|
|||
|
|||
Mount Bindings
Jay Pique wrote:
On Fri, 14 Nov 2003 15:23:01 -0000, wrote: Tooling you'll need -- * drill press Not in any of the shops I've seen doing mountings. Agreed. Shops have jigs instead, which makes hole placement easier (although I've seen some carefully mis-placed holes on new skis come out of shops) - if you don't have a jig, a drill press can help you place (and control depth of) the holes. |
#8
|
|||
|
|||
Mount Bindings
|
#9
|
|||
|
|||
Mount Bindings
lal_truckee wrote:
wrote: I have a little story about a ski patroller who caught me readjusting my bindings at the top of the lift ... And? Are you going to say there's a mountain where they discourage self-reliance? My local hill puts at several workbenches scattered around the hill, with tools (chained to the bench, naturally - there are boarders around) for binding self-adjustments and general repairs. We've got those here, but the damn chains are just short enough and the table is just high enough that I have to take my boots off in order to use the damn screwdriver to adjust one of the settings. I need to do more stretching exercises. -- Cheers, Bev ================================================== ============== "Everything sucks; reverse the wires and everything will blow." -- Desert Ed |
#10
|
|||
|
|||
Mount Bindings
lal_truckee wrote: wrote: I have a little story about a ski patroller who caught me readjusting my bindings at the top of the lift ... And? Are you going to say there's a mountain where they discourage self-reliance? Actually, on this trip I'd rented demo boards and skiied on them a couple days but took my old Volants with me to the hill. I thought I'd do a few runs on the old stuff to compare. Naturally, I didn't notice until I'd skiied about 50 yards off the top of the first lift that I'd loosened the binding settings back to zero for storage. No big deal, except that a patroller saw me (clad in Texan neon) skid up to a bench, take off both sticks, and start cranking like hell on all the binding screws. He asked "what the hell are you DOING?" I muttered something about "the last guy who tuned these" but he left me alome when he saw that I at least appeared to have a clue about what I was doing. That wasn't as bad as the first time I used my adjust-o-matic Salomon Equipe boots (1992) and had to swap the cant plates from one boot to the other ... halfway up the hill at the Heave. Nowadays I pay bootfitters to ply their trade. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Good Indo on Decks, Boots, and Bindings?? | Barry Dinglehopper | Snowboarding | 4 | January 2nd 04 03:25 PM |
NNN Auto Bindings | Author | Nordic Skiing | 4 | December 19th 03 10:13 PM |
salomon bindings / burton boards | Joe | Snowboarding | 6 | December 18th 03 09:48 PM |
Flow Bindings | mr E | Snowboarding | 1 | November 15th 03 06:32 AM |
Atomic Ski Bindings - 4.12 or 6.14 which is better for me? | Christopher Luke | Alpine Skiing | 7 | August 10th 03 03:40 PM |