If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Bindings mount
I have just purchased a pair of skis without bindings mounted. It has a
horizontal line at around the binding position and there are two numbers with a drill icon. 3.6mm and 9.5mm. I assume the line is at center of boot, two number are drill size and depth. Am I right ? TIA. |
Ads |
#2
|
|||
|
|||
I think you're right!
The line in around the middle of the ski should be concordant with the sign at the side of the sole of your boot. Just in order to make it su Don't use a drill size of 9.5 and a depth of 3.6 - this will definitly help;-) Have fun with your new stuff! RicciE Yum wrote: I have just purchased a pair of skis without bindings mounted. It has a horizontal line at around the binding position and there are two numbers with a drill icon. 3.6mm and 9.5mm. I assume the line is at center of boot, two number are drill size and depth. Am I right ? TIA. |
#3
|
|||
|
|||
Thanks !
"R Ebert" wrote in message ... I think you're right! The line in around the middle of the ski should be concordant with the sign at the side of the sole of your boot. Just in order to make it su Don't use a drill size of 9.5 and a depth of 3.6 - this will definitly help;-) Have fun with your new stuff! RicciE Yum wrote: I have just purchased a pair of skis without bindings mounted. It has a horizontal line at around the binding position and there are two numbers with a drill icon. 3.6mm and 9.5mm. I assume the line is at center of boot, two number are drill size and depth. Am I right ? TIA. |
#4
|
|||
|
|||
"Yum" wrote in message ... I have just purchased a pair of skis without bindings mounted. It has a horizontal line at around the binding position and there are two numbers with a drill icon. 3.6mm and 9.5mm. I assume the line is at center of boot, two number are drill size and depth. Am I right ? TIA. I would spend the $30 - $45 to have them mounted by a good ski shop. This way you will know it is done correctly and the bindings tested and adjusted properly. JQ Dancing on the edge |
#5
|
|||
|
|||
JQ wrote:
"Yum" wrote I have just purchased a pair of skis without bindings mounted. It has a horizontal line at around the binding position and there are two numbers with a drill icon. 3.6mm and 9.5mm. I assume the line is at center of boot, two number are drill size and depth. Am I right ? TIA. I would spend the $30 - $45 to have them mounted by a good ski shop. This way you will know it is done correctly and the bindings tested and adjusted properly. Agreed. I would have posted the exact same advice, but I'm getting tired of sounding like a broken record. -- //-Walt // // Proud Member of the Reality-Based Community |
#6
|
|||
|
|||
Yum wrote:
I have just purchased a pair of skis without bindings mounted. It has a horizontal line at around the binding position and there are two numbers with a drill icon. 3.6mm and 9.5mm. I assume the line is at center of boot, two number are drill size and depth. Am I right ? TIA. Some ski manufacturers mark boot midsole (most common, I believe) some mark toe, some don't mark and expect you to measure either cord length, or running surface length and make your own mark. Make sure you know which you've got - you didn't mention the ski manufacturer. Don't forget to tap the holes if required. You do know whether it's required, don't you? Be very careful adjusting your drill stop so you don't dimple the bases, or worse, punch right through. If you're serious about this, use the paper template that comes with the bindings (they did give you the template, didn't they?) to drill a piece of 1/4 inch plastic to use as a drill guide; make sure the bindings and plastic holes are properly aligned, then clamp the guide to the skis at the correct position to guide your drilling - can save allot of heart-ache. Finally, there's more You'll need to know about setting the bindings than just setting DIN to your weight. There's a good reason shops get a few bucks to mount bindings. Also, if you buy bindings and skis from the same shop mounting is soemtimes free, or at least discounted. |
#7
|
|||
|
|||
Hi there.
Even though I've given some hints for mounting the bindings I totally agree with all the others that you surely ought to know what oyu're doing! Even more if you're considering that getting the binding mounted by a professional gives you a warranty that you'll loose by doing it yourself... RicciE |
#8
|
|||
|
|||
"lal_truckee" wrote in message ... Yum wrote: I have just purchased a pair of skis without bindings mounted. It has a horizontal line at around the binding position and there are two numbers with a drill icon. 3.6mm and 9.5mm. I assume the line is at center of boot, two number are drill size and depth. Am I right ? TIA. Some ski manufacturers mark boot midsole (most common, I believe) some mark toe, some don't mark and expect you to measure either cord length, or running surface length and make your own mark. Make sure you know which you've got - you didn't mention the ski manufacturer. Don't forget to tap the holes if required. You do know whether it's required, don't you? Be very careful adjusting your drill stop so you don't dimple the bases, or worse, punch right through. If you're serious about this, use the paper template that comes with the bindings (they did give you the template, didn't they?) to drill a piece of 1/4 inch plastic to use as a drill guide; make sure the bindings and plastic holes are properly aligned, then clamp the guide to the skis at the correct position to guide your drilling - can save allot of heart-ache. Finally, there's more You'll need to know about setting the bindings than just setting DIN to your weight. There's a good reason shops get a few bucks to mount bindings. Also, if you buy bindings and skis from the same shop mounting is soemtimes free, or at least discounted. Thank you for good suggestions. I am planning to use bindings mounted on a old pair of skies. So, I don't have a template, but I can measure the distance between holes on a old ski. Since I use the same boots, I don't think I need to readjust binding settings, I presume. Yes, I understand ski manufactures want to discourage people from trying it for liability reason. In my case, it seems to be a simple enough task. Isn't it just a matter of drilling right size holes at right location ? Or am I missing something ? Is there any reason, kids at ski shop can do a better job than others ? Does it requre special tools or skills ? I tried to find information on the net, but couldn't find any. Thanks. |
#9
|
|||
|
|||
"JQ" wrote in message ... "Yum" wrote in message ... I have just purchased a pair of skis without bindings mounted. It has a horizontal line at around the binding position and there are two numbers with a drill icon. 3.6mm and 9.5mm. I assume the line is at center of boot, two number are drill size and depth. Am I right ? TIA. I would spend the $30 - $45 to have them mounted by a good ski shop. This way you will know it is done correctly and the bindings tested and adjusted properly. JQ Dancing on the edge Thank you for the advice. I may end up doing as you suggested.. Howver, it looks to me like a very simple job that anybody can handle. It takes only few seconds for guys at ski rental shop adjusting binding for different boots. I feel I can spend more time and do a better job. Or, am I missing something ? |
#10
|
|||
|
|||
"lal_truckee" wrote in message ... Yum wrote: I have just purchased a pair of skis without bindings mounted. It has a horizontal line at around the binding position and there are two numbers with a drill icon. 3.6mm and 9.5mm. I assume the line is at center of boot, two number are drill size and depth. Am I right ? TIA. Some ski manufacturers mark boot midsole (most common, I believe) some mark toe, some don't mark and expect you to measure either cord length, or running surface length and make your own mark. Make sure you know which you've got - you didn't mention the ski manufacturer. Atomic ski and Marker binding. Don't forget to tap the holes if required. You do know whether it's required, don't you? Be very careful adjusting your drill stop so you don't dimple the bases, or worse, punch right through. No, I didn't know. I guess they are metic. Correct ? Thanks. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
NNN Auto Bindings | Author | Nordic Skiing | 4 | December 19th 03 10:13 PM |
salomon bindings / burton boards | Joe | Snowboarding | 6 | December 18th 03 09:48 PM |
Mounting alpine bindings | Terry Hill | Alpine Skiing | 26 | December 6th 03 05:51 AM |
Mount Bindings | Schmoe | Alpine Skiing | 12 | November 15th 03 03:02 PM |
Atomic Ski Bindings - 4.12 or 6.14 which is better for me? | Christopher Luke | Alpine Skiing | 7 | August 10th 03 03:40 PM |